Wireless Controls and Automation  
   
 
Industrial Wireless Long Range Radio Controls 
 
Applications:  Industrial Monitoring, Pump control, Monitor remote sites, Tank Level, Lighting control, Remote Mobile system, PLC remote, Irrigation, Gates. Factory process control, Traffic management and Signaling, Alarms, Generators, Marinas, Solar systems,  Wire replacement.  

Heavy Duty Extended Range M154 Radios


.......

Performance  3 miles ( 5 Km )
 Extended range up to 20 Km
• Not limited to line-of-sight communication


Migro Encoding/Decoding technology
Four (4) Independent Channels
Output selection: Latch or Momentary
Wide Antenna Selection: Omni, Yagi
Power: 12 VDC - Solar Ready
Dip Switch 12 Bit Code setting
Multiple Transmitters and Receivers
Optional repeater if necessary
Factory pre- configured system, Ready
No setup or programming required
No fees from carriers, No hacking
No software or internet required

 

 

MXT-4 VHF Transmitter   $899.99      
Special Order, Power Pulse Transmitter
MXT-48  PWTransmitter $1,499.99
 
  
MXR-4 Receiver   $989.99   
   
   Specifications     M154T  Digital Transmitter  
Supply power  12VDC /  8Watt 
Inputs  N/O Normally Open, digital dry contact
Transmitter power per FCC Part 15.249,  50mV/m @ 3m
MXT-4 32dBi VHF GFSK
MXT-48 FM VHF  Power-Pulse
Frequency 154MHz  • License free MURS band
Transmission Digital Encoded  Gaussian_frequency-shift_keying.   
Channels 16 addresses per system 
Power draw Standby 1mA, Transmission 1200mA Solar Ready
Response Loop 500 msec
Weight 5.36 lb ( 2.44kg )  each unit
Dimensions Weatherproof, IP66,  9" W x9" H x 4" D  8900
   Specifications      M154R  Digital Receiver   
Supply power  12VDC /  5Watt 
Output   Relay 8Amp, SPDT (NO/NC) Class 2 Pilot Duty
Output mode Momentary or Latching, Optional Continuous (*)
Configuration DIP switch factory preset
Compliance FCC CFR part 15.247, 95 sub E
Power draw Standby 30mA, Full load 400mA
Antenna Z 50 Ohm, RF Connector  SO-239
Ambient temp  14° to 140° F (-10° to 60° C)
Enclosure Weatherproof , IP65,  9" W x9" H x 4" D  9600
 
Wiring Terminals

FCC Certified ID: OHKFMT154
COMPLIANCE: per FCC Part 15.249, 50mV/m @ 3m
Circuit board Compliance with UL796 and UL 94
MIL-STD-461E for Electro-Magnetic Interference (EMI)
MIL-STD-901D Grade A for High Impact Shock
MIL-STD-167B for Vibration
 

  Accessories

          Antennas

    Control Modules

 

 


ANTENNA Selection 154Mhz - 50 Ohm:

Short Range

Medium Range

Long Range

Long Range
 
931501 931487 931487 931490 931503 Yagi 3 Element  
2.0 dBi,  17 inch 4.5 dBi, 37 inch SO-239 & 12ft Coax 6.7 dBi, 125 inch 9.2 dBi, 42 inch  
PL-259 SO-239 & 12ft Coax TWO Antennas SO-239 SO-239  
931501    $79.99
  

931487    $159.99 
  

Two 931487    $299.99 
  

931490   $299.99
   
931503  Yagi   $399.99
  
 

Optional (*) Control Modules:

Single channel continuous mode module (FCC Compliant)

OPERATION:  Transmitter sends an interval pulse as long as the input is activated by a control, switch or sensor etc. The Receiver at the other end  turns the output ON decodes the interval to verify the status of the transmitter, If The Transmitter Ends  the control action, or loss of power or carrier, then The receiver decoder will acknowledge and  turn the Receiver output OFF   until the signal is activated again 
By Example:  In a Pump Control,  When the float Sw Closes, Transmission starts, and the Receiver activates  the output Relay ON , it will maintain these status until the Float Sw Opens then  after the  time preset (ex, 30sec) deactivates the output Relay OFF   
Fail Safe sequence mode, Modules        NOTE  FCC  Timing Compliance 

Fail Safe sequence module, Power, Carrier failure or end of transmission control
Comply with FCC part 15.247 sub E on Continuous transmission timing


9FS1   Receiver Module

Operating voltage 12VDC
Input:  Dry Contact
Output:  10A SPDT
Enclosure Weatherproof IP65,  9x9x4 inches


NOTE: Transmitter or  receiver not supplied,

9FS1 Single Channel Fail Safe Module   $398.99
 
   


Four (4) channel continuous mode module  (FCC Compliant)

 
Fail Safe sequence module, Power, Carrier failure or end of transmission control
Comply with FCC part 15.247 sub E on Continuous transmission timing


9FS4   Receiver Module

Operating voltage 12VDC
Input:  Dry Contact
Output:  8A SPST
Enclosure Weatherproof IP65,  9x9x4 inches

NOTE: Transmitter or receiver not supplied,

9FS4 Four (4) Channel Fail Safe Module   $698.99
 
   


Start/Stop output Module  

Operation:

Transmitter send a momentary pulse via Channel One (1)  to START;  the Receiver Control Module Output  turns ON 
 It will stay ON Until the transmitter  sends the STOP signal via Channel Two (2) to turn the Receiver Output OFF

Start Stop Mode Receiver Module


9SS1:  Two input  from the receiver,  
One output to energize the external contactor

Operating voltage 12VDC
Input:  Dry Contact
Output:  10A SPDT
Enclosure Weatherproof IP65,  9x9x4 inches

NOTE: Transmitter and receiver not supplied,

9SS1   Start Stop Module  $399.99
 
   


Hybrid Battery Backup Module

9HBU:  12 VDC Charge Controller and Regulator,  
              Can be used as Battery Backup or Solar Charger

Operating voltage
 
Input:     120/240VAC  or 12VDC

Output:  12VDC,  5.Amp 

Enclosure Weatherproof IP65,  9x9x4 inches

Battery Space Size up to 20Ah ( Battery Not included )

NOTE: Transmitter and receiver not supplied,

9HBU   Battery Backup Module  $199.99
 
   

 


Transmitter wiring
 

  Board Transmitter  Configuration
 
 
 
 
OEM  Transmitter Box Configuration ( Same as Board Settings )
 

 
 

 Control modules Add On Required  to Comply with FCC part 15.247 sub E on Continuous transmission timing


  

DISCLAIMER:
Radio control equipment in not to be used in life safety.

Radio Installations shall be performed by a certified professional
 

 

     Copyright ©  Electrodepot. All rights reserved